Komatsu SAA6D170E-5 long block: what is included, part numbers, selection and REMAN
Komatsu SAA6D170E-5 long block: what the assembly includes, part numbers 6245-LE-0100 and RM6245-LE-0100, how it differs from a short block, how to select it by Engine S/N and when our REMAN long block fits. Engine reference data included.
In short: what you need to know about the Komatsu SAA6D170E-5 long block
- Long block. It is the engine «without the dressing»: cylinder block, crankshaft, pistons with connecting rods, cylinder heads with valves, camshaft and oil pump, assembled; the turbocharger, manifolds and electronics are carried over from the old engine. In the Komatsu parts catalogue the long block of this engine is listed under the numbers 6245-LE-0100 (new) and RM6245-LE-0100 (remanufactured, RM prefix).
- From us. Remanufactured (REMAN) long block for Komatsu SAA6D170E-5: product page. The first batch is 3 units, expected in February 2027 at the warehouse in Guarulhos (São Paulo).
- How we select. The assembly is selected along a chain: Komatsu number → arrangement letter (-5A, -5BR, -5C…) → engine serial number (ESN) → machine model and serial number. This way the long block fits your machine exactly.
- Which engine. An inline six-cylinder Komatsu diesel with a displacement of 23.15 L (bore and stroke 170 × 170 mm), turbocharged, with charge-air cooling and an electronic Common Rail fuel system. Tier 3 / Stage 3A generation («ecot3»).
- How many horsepower. There is no single figure: gross power depends on the machine, from 396 kW (531 hp) on the WA600-6 loader to 552 kW (740 hp) on the HD465/HD605-7 trucks. The D375A-6 dozer is rated at 474 kW and the PC1250-8 excavator at 515 kW.
- Where it is fitted. HD465-7 and HD605-7 trucks, D375A-5/-6 dozers, the WD600-6 wheeled dozer, PC1250-8 excavators and WA600-6 loaders — 18 models and variants in all (with the E0 and R indices).
How to read this article. If you are a buyer selecting a unit — Part I (sections 1–5): what a long block is, what it includes, the part numbers, selection and our REMAN unit, plus the questions and answers at the end. If you want to understand the engine it is built for — Part II (sections 6–8, in plain language). If you are an engineer or mechanic — Part II (sections 9–12: design, arrangements, specifications) and Part III (dimensions, torques, standard values, part numbers). Part III is reference material: it need not be read in sequence.
Part I. The long block: what it is, what is included and how to choose it
1. What a long block is and how it differs from a short block
A long block is the engine «without the dressing»: the lower part with crankshaft, pistons and cylinder block, plus assembled cylinder heads with valves and the valve train. For the owner it is an intermediate option between repairing by assemblies and buying a complete engine: the turbocharger, fuel system, manifolds, electronics and other attached equipment are transferred from the old engine.
| Assembly | Meaning | Cylinder heads | Attachments and systems |
|---|---|---|---|
| Cylinder Block | The bare block or its assembly in a particular configuration | Not implied automatically | Not implied |
| Short Block | Lower mechanical assembly of the engine | Usually not | Per the specification; oil cooler — optional |
| Long Block | A fuller mechanical assembly with heads and valve train | Yes (per Komatsu's typical configuration) | Partly; the scope differs by engine type |
| Complete Engine | The whole power unit | Yes | Scope of ancillaries, electronics, starter, alternator and exhaust devices — per the unit's specification |
The short block per the Komatsu reference is the cylinder block, crankshaft, pistons, connecting rods, liners and (optionally) the oil cooler. The scope is defined by the number and the unit's specification.
2. What the long block includes and what is transferred from the old engine
Typical long block configuration per Komatsu (13 items)
A typical long block configuration includes:
- Cylinder Head Assembly — complete cylinder heads;
- Intake & Exhaust Valves — intake and exhaust valves;
- Cylinder Block — cylinder block;
- Front Drive Gears — front drive gears;
- Crankshaft — crankshaft;
- Pistons & Connecting Rods — pistons and connecting rods;
- Camshaft & Camfollower Assembly — camshaft and cam followers;
- Rocker Arm Assembly — rocker arms;
- Oil Pump Assembly — oil pump;
- Front Gear Cover — front gear cover (optional);
- Oil Cooler Assembly — oil cooler (optional);
- Water Pump Assembly — water pump (optional);
- Injectors — injectors.
The front gear cover, oil cooler and water pump are supplied as options; injectors are part of the long block for electronic fuel systems. The scope of each unit is stated in its specification.
What usually has to be transferred from the old engine or bought separately
As a rule (the final list for a specific unit is fixed in the specification): the injection system (injectors, fuel pump, fuel rail), the KTR130E turbocharger, the charge-air cooler, the intake and exhaust manifolds, the EGR system (on versions without «R»), the flywheel and flywheel housing, the torsional vibration damper, the starter, the alternator, sensors, the electronic control unit and wiring harness, the oil pan, filters, brackets and — if not ordered as options — the front gear cover, oil cooler and water pump.
Installation recommendations (general): replace all filters and fluids; flush the cooling system and radiator; flush or replace the oil cooler (especially after a failure with metal debris); inspect the turbocharger, charge-air cooler and injectors; prime the engine with oil before the first start; follow the tightening torques and run-in procedure from the Komatsu manual; record the long block serial number at installation.
3. New and REMAN: which numbers exist
Long block numbers in the Komatsu parts catalogue
The long block of the SAA6D170E-5 engine appears in the Komatsu nomenclature under two numbers:
- 6245-LE-0100 — long block (new number, no prefix);
- RM6245-LE-0100 — a long block with the RM prefix; in Komatsu numbering the RM prefix denotes a remanufactured (reman) assembly. This is the reman variant of the 6245-LE-0100 long block.
The 6245 series in Komatsu numbering belongs to the SAA6D170E-5 engine: the cylinder block, head, crankshaft, short blocks and long block.
Short blocks: four numbers by machine group
| Number | Machines | Engine |
|---|---|---|
| 6245-SE-0011 | HD465-7E0, HD465-7R, HD605-7E0, HD605-7R | SAA6D170E-5 |
| 6245-SE-0021 | D375A-5E0, D375A-5R, D375A-6, D375A-6R | SAA6D170E-5 |
| 6245-SE-0031 | PC1250-8, PC1250LC-8, PC1250SP-8 and -8R variants | SAA6D170E-5 |
| 6245-SE-0041 | WA600-6, WA600-6R | SAA6D170E-5 |
The numbers 6245-SE-0031 and 6245-SE-0041 are also in the Komatsu parts catalogue. These are short blocks, not long blocks. Each group of machines has its own number — so we select the assembly for your machine.
What «RM» and «R» are: two different abbreviations
- RM at the start of a part number (RM6245-LE-0100, RM6245-A0-0030) marks Komatsu's remanufactured nomenclature.
- R at the end of a machine name (D375A-6R, PC1250-8R, WA600-6R, HD465-7R) is a regional version of the machine, not «reman». According to the Komatsu manual, the engines of these versions are built without the EGR system (the weight tables have a separate «EGR-less» table), and the D375A-6R/WA600-6R/WD600-6R brochures give the emissions level as Tier 2 / Stage 2 (equivalent).
- E0 (HD465-7E0, D375A-5E0, PC700-8E0) is the designation of the version with a Tier 3 engine; in these versions the engine has an EGR system.
4. How to select a long block: five steps
Selection is a chain of checks: Komatsu part number → exact engine arrangement (letter) → Engine S/N → machine model → Machine S/N → current Komatsu parts catalogue → check of supersessions and scope. The more precise the data, the faster we select the right unit. Engine S/N and Machine S/N are different identifiers: the engine serial number belongs to the power unit, the machine number to the base machine, and after an engine replacement they may not match the machine's initial configuration.
What the buyer should prepare
- Full engine name — SAA6D170E-5 with the letter suffix and additional designations.
- Engine S/N — a photo of the nameplate and a legible character sequence.
- Machine model — do not shorten HD465-7R to HD465-7 or D375A-5E0 to D375A-5.
- Machine S/N — the machine serial number.
- The assembly level you need — cylinder block, short block, long block or complete engine.
- Condition of the unit — new or REMAN.
- Actual scope of supply — with or without heads, oil pump, oil cooler, water pump, injectors — per the specification of the specific unit.
- Number of the previous part — if available, including markings and replacement history.
- Regional arrangement — emissions version, cooling scope, EGR, Common Rail, electrical components and mounting accessories.
- Commercial terms — photos of the actual goods, packaging, availability and an individual warranty — only after confirmation.
How to request a long block from us
To select a long block, all we need is: Engine family + full suffix + Engine S/N + Machine model + Machine S/N + photos of the nameplate and of the engine from all sides. From these data we determine the arrangement, select the unit and send you its specification.
Can a long block from a WA600-6 be fitted to a D375A-6? A long block is selected for a specific engine arrangement: the WA600-6 and D375A-6 have different arrangements and different short block numbers, so we check the catalogue number and Engine S/N and select the suitable unit.
5. Our REMAN long block for the SAA6D170E-5
The site has a dedicated page «REMAN long block for Komatsu SAA6D170E-5 engine» (machines: PC1250-8, D375A-6, HD465-7R, HD605-7R, WA600-6 and their variants). It is a remanufactured (REMAN) long block for a Komatsu engine. An original Komatsu Reman remanufactured unit, not a copy. Identification data for each unit (nameplate photo, serial number) are provided on request and, for the batch in transit, after it arrives at the warehouse.




- First batch: 3 units, expected in February 2027 at the CATKOMPARTS warehouse in Guarulhos (São Paulo state, Brazil). Supply to other countries on request; condition: payment before shipment.
- Scope: the typical long block configuration is given in section 2. The front gear cover, oil cooler and water pump are optional; injectors depend on the configuration. The scope of each unit is stated in its specification.
- Reference numbers: 6245-LE-0100 and RM6245-LE-0100 — for identification and catalogue search.
- The warranty on the long block is agreed individually and recorded in the specification and invoice.
- How to order: send a photo of the engine nameplate (full model with the letter and ESN), the machine model and serial number, and photos of the old engine from the front and both sides, via the form on the site or on WhatsApp. We will check the arrangement and serial range and send the unit specification.
Parts of this engine for your own assembly: cylinder block 6245-21-1100, cylinder head without valves 6245-11-1100, crankshaft assembly 6245-31-1100, camshaft assembly 6245-41-1100, connecting rod assembly 6245-31-3100, piston 6245-31-2110. We confirm the exact number for your engine by its Engine S/N.
Part II. The SAA6D170E-5 engine: in plain language and for the engineer
6. What the SAA6D170E-5 is and how to decode the name
Komatsu SAA6D170E-5 is a power unit for Komatsu's heaviest equipment: mining trucks, dozers, excavators and wheel loaders. The engine is designed for long shifts under heavy load, where the cost of downtime is measured not in hours but in tonnes of rock not shipped.
The name reads from left to right (this is how Komatsu engine designations are built):
- S — turbocharging; AA — charge-air cooling in the «air-to-air» scheme (simpler engines have a single «A»);
- 6D — six cylinders in line, diesel; 170 — cylinder bore in millimetres;
- E — generation designation; -5 — engine series;
- the letter after the series (for example, -5A, -5BR, -5C, -5EE) — the arrangement for a specific machine: power, attached equipment, sometimes internal parts. The full designation with the letter and the engine serial number (ESN) are stamped on the engine nameplate.
The family is also simply called «6D170». In advertisements this name often mixes the -2, -3, -5, -6 and -7 generations, but these are different engines, each with its own parts (details in section 10).
A short history
The SAA6D170E-5 series is Komatsu's Tier 3 generation under the «ecot3» brand. In Komatsu America press materials it appears in 2008: at CONEXPO 2008 the HD605-7 truck was shown already with the SAA6D170E-5 engine, whereas the first HD465-7 and HD605-7 in 2006 were described with the SAA6D170E-3 generation. In August 2009 the D375A-6 dozer was released with a net power of 610 hp, and in October 2009 the WD600-6 wheeled dozer.
The technical highlight named in the PC1250-8 brochure is the cooled exhaust gas recirculation (EGR) system with an electronically controlled venturi and bypass — according to Komatsu, the first of its kind in the world; NOx emissions are cut by 40 % with no loss of power. The successor, the SAA6D170E-7 engine of the new-generation machines (HD465-8/HD605-8, D375A-8, WA600-8, PC1250-11), is already a different design.
7. Scale: figures worth remembering
To get a feel for the size of this engine, it helps to turn the specification data into everyday quantities.
- One cylinder holds about 3.86 L (23.152 L ÷ 6), almost like a four-litre can; the whole engine is six such «cans».
- A piston with its connecting rod weighs 22 kg, the rod alone about 10.3 kg; the crankshaft 265 kg; the 6 cylinder heads 46.5 kg each; the cylinder block assembly with liners 750 kg.
- Piston stroke 170 mm. At 1,800 rpm the mean piston speed is 10.2 m/s, at 2,000 rpm 11.3 m/s (calculation: 2 × stroke × speed).
- Cylinder pressure. At the 3,324 N·m torque of the HD465/HD605 truck, the brake mean effective pressure is about 18 bar (calculated with the formula 4π·T/V; for the PC1250-8 about 16.4 bar, for the WA600-6 about 14.1 bar).
- Dry weight of the engine: from 2,970 to 3,180 kg depending on the arrangement; length from 1,783 to 1,867 mm.
- Fuel consumption at rated power: from 216 g/(kW·h) on the truck to 227 g/(kW·h) on the dozer and loader.
- Firing order: 1-5-3-6-2-4; seven crankshaft main bearings; for each cylinder, two oil jets cooling the piston crown.
- Oil: engine oil fill capacity 80 L; coolant in the engine itself 44 L.
The question «how many horsepower does the SAA6D170E-5 have?» therefore has no single answer. Komatsu publishes gross power (SAE J1995) and net power (ISO 9249 / SAE J1349); net is lower because it is measured with the equipment installed. Metric «horsepower» (PS) differs from American hp by a further 1.4 % (552 kW is 740 hp or about 750 PS), so when comparing figures from different brochures the unit and the standard matter. In the European edition of the D375A-6 brochure the 474 kW rating is given at 1,900 rpm, in the American one at 1,800 rpm: speeds and settings also depend on the market.
8. Where this engine works
All the machines below are equipped with the SAA6D170E-5 (according to official Komatsu brochures and reference lists). The same engine model works in very different duty cycles: on a truck, a long haul under load; on an excavator, matching with the hydraulic pumps; on a dozer, pulling at the limit; on a loader, cycles of acceleration and loading. That is why the power, control, cooling and attached equipment differ between arrangements, and choosing parts «by cylinder bore» is not acceptable.
| Machine | Equipment type | Gross power | Net power | Speed |
|---|---|---|---|---|
| HD465-7R | Rigid-frame mining dump truck | 551 kW / 739 hp | 533 kW / 715 hp | 2,000 |
| HD465-7E0 | Rigid-frame mining dump truck | 551 kW / 739 hp (per the published listing) | — | per the specification |
| HD605-7R / HD605-7E0 | Mining dump truck | 551 kW / 739 hp | 533 kW / 715 hp | 2,000 |
| D375A-6 / D375A-6R | Crawler dozer | 474 kW / 636 hp | 455 kW / 610 hp | 1,800 |
| D375A-5E0 / D375A-5R | Crawler dozer (previous model) | 452 kW / 606 hp (engine manual) | — | 1,800 |
| PC1250-8, PC1250LC-8, PC1250SP-8 (and -8R) | Heavy hydraulic excavator | 514 kW / 688 hp (515 kW / 690 hp in the manual) | 502 kW / 672 hp | 1,800 |
| WA600-6 / WA600-6R | Wheel loader | 396 kW / 530 hp | 393 kW / 527 hp | 1,800 |
| WD600-6 / WD600-6R | Wheeled dozer | 396 kW / 530 hp | 393 kW / 527 hp | 1,800 |
Small differences in the figures (551 and 552 kW, 514 and 515 kW) come from rounding in the brochures and in the repair manual. The power output depends on the machine the engine is fitted to.
Links to the machine pages in our catalogue: HD465-7R, HD465-7E0, HD605-7R, HD605-7E0, D375A-6, D375A-6R, PC1250-8, PC1250-8R, WA600-6, WA600-6R. The engine in our applicability guide: SAA6D170E-5.
Full application list (engine, not long block)
The Komatsu short-block reference and the machine brochures give the following breakdown (a machine in the list means the engine model SAA6D170E-5 is fitted to it):
- Mining dump trucks: HD465-7E0, HD465-7R, HD605-7E0, HD605-7R.
- Crawler dozers: D375A-5E0, D375A-5R, D375A-6, D375A-6R.
- Hydraulic excavators: PC1250-8, PC1250LC-8, PC1250SP-8 and the PC1250-8R, PC1250LC-8R, PC1250SP-8R versions.
- Wheel loaders: WA600-6 and WA600-6R.
- Wheeled dozers: WD600-6 and WD600-6R.
Particulars of the individual machine families
- PC1250-8, PC1250LC-8, PC1250SP-8 and the R indices. The excavators work under a high hydraulic load; the brochure highlights the interaction of the electronic engine control with the hydraulic system, the Power/Economy modes, automatic engine-speed reduction and electronic fan control. In the catalogues the PC1250-8 group uses the -5C engine arrangement and the regional versions use -5CR.
- D375A-5E0, -5R, -6 and -6R. The D375A-6 brochure states 474 kW gross at 1,800 rpm, electronic control, cooled EGR and charge-air-cooled turbocharging. For the cylinder block and several other parts of the D375A-6 and D375A-6R, the parts books give their own starting serial ranges — we take them into account when selecting.
- HD465-7E0, HD465-7R, HD605-7E0, HD605-7R. The Komatsu specification for the HD465-7R states 551 kW gross, 533 kW net, 3,320 N·m and a Common Rail system. Do not confuse the HD465-7 and HD605-7 without a suffix with the HD465-7E0/-7R and HD605-7E0/-7R: in the Komatsu reference, the HD465-7 without the E0/R index has the earlier SAA6D170E-3 generation.
- WA600-6, WA600-6R, WD600-6, WD600-6R. 396 kW gross, 393 kW net, 1,800 rpm, electronic control, cooled EGR (on versions without «R») and a hydraulic fan drive. The WA600-6 and WD600-6 brochures declare Tier 3 / Stage 3A; the WA600-6R and WD600-6R documents declare Tier 2 / Stage 2 (or equivalent). The EGR, exhaust path and electronic settings depend on the machine version — we select the unit for your machine.
9. Engine design by assembly
The 170E-5 series is the successor of the 170E-3 series. According to Komatsu's description it is an inline six-cylinder four-stroke liquid-cooled diesel with an electronic Common Rail fuel system and (on versions without the «R» index) a cooled EGR system. Below are the assemblies in the order in which it is convenient to check them when inspecting or selecting a long block.
9.1. Cylinder block and liners
- A cylinder block with seven main bearing supports for the crankshaft and seven camshaft supports (the camshaft sits high — «high cam»). The main bearing cap bolts are tightened into the plastic zone (with an additional angle), so their reuse must follow the manual strictly.
- Wet liners (the coolant washes the liner directly). The inner surface has plateau honing and tufftriding (nitriding). Sealing: at the top a «clevis seal» gasket, in the middle an ethylene-propylene rubber ring, at the bottom a silicone rubber ring.
- Two oil jets cooling the piston crown per cylinder (12 in total). For the SAA6D170E-5 Komatsu separately notes improved «double» cooling jets compared with the 170E-3.
- For the EGR version the block is partly modified (for the cooled recirculation), but the block dimensions remained the same — this is stated in the engine description itself.
- Front seal; rear seal with a dust lip.
9.2. Crankshaft, connecting rods, pistons
- Crankshaft — forged special alloy steel, 7 main bearing journals, journals hardened by induction. The main and rod bearing shells are three-layer (kelmet); the upper main bearing shell has an oil groove. Journal undersizes: 0.25 / 0.50 / 0.75 / 1.00 mm (details in section 13).
- Catalogues list bare crankshafts and the «crankshaft assembly» (Crankshaft Assembly) with additional components separately — these are different catalogue items. A set of main bearing shells for one journal and a full repair kit for the engine are also not equivalent.
- Connecting rod — forged alloy steel, weight 10.29 ± 0.03 kg; the spare small-end bushing is semi-finished (finished to fit the pin).
- Piston — ductile (spheroidal graphite) cast iron (FCD), a «shaker» cooling cavity, a two-stage re-entrant combustion chamber; Komatsu states a reduced coefficient of thermal expansion. Rings: the top ring has an inner cut, a barrel-shaped working face and an ion coating; the second ring has an inner cut, a tapered face and hard chrome; the oil ring has a bevelled edge and a nitrided face.
- Komatsu catalogues contain both piston numbers —
6245-31-2110and6246-31-2110. The piston is selected by engine arrangement and serial range.
9.3. Cylinder heads and valve train
- The heads are separate — one head per cylinder (6 pieces, 46.5 kg each), with 4 valves per cylinder; the intake and exhaust seats are pressed in. Direct fuel injection.
- The camshaft (7 supports) is made of special carbon steel, with journals and lobes induction-hardened; the drive is through roller followers, pushrods, rocker arms and crossheads («cross head») that open two valves at once.
- In catalogues you need to distinguish «shaft» from «camshaft assembly» and take into account the components included in the assembly (followers, pushrods, rocker arms, crossheads, adjusting screws and nuts), so as not to count one part twice.
- Valve clearances on a cold engine: intake 0.32 mm, exhaust 0.62 mm (tolerance ±0.02).
- Per engine: 6 complete heads, 12 intake and 12 exhaust valves, 12 crossheads and 24 valve stem seals (two valves of each type per cylinder — four valves per cylinder).
9.4. Drive and gears
The engine has two gear trains. The front one (driving the auxiliaries): crankshaft gear 55 teeth, large idler 84, oil pump 38, water pump 31, small idler 67, alternator 55; on the EGR version an EGR oil pump drive gear of 43 teeth is added. The rear one (driving the camshaft and fuel pump): crankshaft gear 63, idlers 72 and 40, camshaft gear 70, high-pressure fuel pump drive gear 70. Backlash values are in section 13. The flywheel ring gear has 118 teeth (138 on the D375A-5E0 and D375A-5R).
9.5. Lubrication
- Gear-type oil pump (10 + 10 teeth), speed 1.45 crankshaft revolutions; relief valve and three combination filters of 0.44 m² each (the filter valve opens at a differential of 441 ± 19.6 kPa).
- Oil coolers: 2 units (9 stages, surface 0.65 m², heat exchange not less than 60,000 kcal/h); the thermostat valve opens at 85 ± 1.5 °C and fully at 100 °C (stroke not less than 8 mm).
- Oil goes to the main gallery, the crankshaft, camshaft, rocker arms, piston cooling jets, gears and the turbocharger; on the EGR version also to the EGR valve through a dedicated EGR oil pump (pressure 1.47 MPa, 15 kg/cm²), which actuates the valve hydraulically.
- The engine oil fill capacity is 80 L (per the engine specification table; the «on the machine» value depends on the oil pan and oil lines of the specific machine).
9.6. Cooling
- The water pump is gear-driven (31 teeth), speed 1.77 crankshaft revolutions, flow 800 L/min at 3,730 rpm.
- Thermostat: starts to open at 76.5 ± 2 °C and is fully open at 90 °C (stroke not less than 9 mm).
- Coolant in the engine itself is 44 L. The fan is driven hydraulically on the machine side (there is no fan belt); the alternator belt has an automatic tensioner.
- Corrosion protection is provided by a corrosion resistor with a solid inhibitor (400, 600 or 1,000 g, depending on the arrangement).
9.7. Air, boost and EGR
- KOMATSU KTR130E turbocharger with water cooling of the bearing housing: dimensions 343 × 390 × 344 mm, weight 35.5 kg; the shaft turns at 50,000–100,000 rpm on floating plain bearings. Komatsu describes it as an improved version of the KTR130 with a more efficient compressor impeller and reinforced material.
- «Air-to-air» charge-air cooler (fitted on the machine).
- Cooled EGR (versions without «R»): the EGR cooler uses corrugated stainless steel tubes; the EGR valve has hydraulic actuation and electronic control (Komatsu's own development); a bypass circuit with a venturi and a bypass valve complements the work of the EGR valve. The valve drive pressure is at least 1.18 MPa at idle and 1.43 MPa at maximum no-load speed. «R» versions do not have these assemblies — the engine is without EGR (the manual gives separate tables for them).
- Electric intake air heater (22 V, 111 A) — for starting at low temperatures.
9.8. Fuel system
- Common Rail: DENSO ECD-U2 high-pressure fuel pump (lubricated with engine oil) and electronic control; injection pressure up to 160 MPa (1,600 kg/cm²) from low to high speeds, multiple injection.
- The main fuel filter with a water separator (filtering area 1.06 m²) and a pre-filter are standard; an electric priming pump. According to Komatsu this allows the use of market-quality fuel of NAS class 12 (in different parts of the manual, class 12 or 13 is given for versions with and without EGR).
- The engine controller is mounted on the engine and has automatic altitude compensation — there is no need to change it for work high in the mountains.
10. Arrangements: letters, serial numbers, EGR and «R», generations
10.1. What -5A, -5BR, -5C… mean
The letter after «-5» defines the arrangement for a specific machine: power, ancillary equipment and sometimes internal parts. The following arrangements are known; starting engine serial numbers are given for reference.
| Arrangement | Machines / group | Starting Engine S/N |
|---|---|---|
-5A | WA600-6 / WD600-6 | 511694-UP |
-5AR | WA600-6R / WD600-6R | 610512-UP |
-5B | HD465-7E0 / HD605-7E0 | 511668-UP |
-5BR | HD465-7R / HD605-7R | 610861-UP |
-5C | PC1250-8 / PC1250LC-8 / PC1250SP-8 | 511700-UP |
-5CR | Regional PC1250-8R / PC1250SP-8R | 610911-UP |
-5E | D375A-6 | 511657-UP |
-5EE | D375A-6R | 610984-UP |
-5F | HD465-7E1 / HD605-7E1 | 513388-UP |
10.2. What «511694-UP» and «610984-UP» mean
«511694-UP» is a range that starts at the stated engine serial number and continues onward within the conditions of the specific publication. Within a book, individual lines may have their own conditions: «from–to», «and above», «up to», «after», supersession number, kit flag, note. We take the conditions of each line into account when selecting parts.
Engine S/N and Machine S/N are different identifiers. The engine serial number belongs to the power unit, the machine number to the base machine. After an engine replacement they need not match the initial configuration.
10.3. «R» versions and EGR: how the engines differ
| Feature | Without «R» (E0, -6, -8…) | With «R» (-5R, -6R, -7R, -8R) |
|---|---|---|
| EGR (cooled recirculation) | Present: cooler, hydraulic valve, venturi bypass, EGR oil pump | Absent («EGR-less» in the manual; separate tables of weights and gears) |
| Emissions level per machine brochures | Tier 3 / Stage 3A | Tier 2 / Stage 2 (or equivalent) |
| Engine weight (dry) | D375A-5E0 — 2,970 kg; PC1250-8 — 3,140 kg; WA600-6 — 3,050 kg; HD-7E0 — 3,120 kg | D375A-5R — 3,029 kg; PC1250-8R — 3,156 kg; WA600-6R — 3,180 kg; HD-7R — 3,028 kg |
| Boost pressure (standard for a new engine, min.) | D375A-5E0 — 141.3 kPa; PC1250-8 — 160 kPa; WA600-6 — 126.6 kPa; HD-7E0 — 160 kPa | D375A-5R — 113.3 kPa; PC1250-8R — 116 kPa; WA600-6R — 94 kPa; HD-7R — 130.6 kPa |
The «R» at the end of a machine name is a regional arrangement and not «reman». The RM prefix at the start of a part number (for example, RM6245-LE-0100) marks remanufactured nomenclature; it is a different designation.
10.4. SAA6D170E generations: -2, -3, -5, -6, -7
Advertisements mention 6D170, SA6D170E, SAA6D170E-2, SAA6D170E-3, SAA6D170E-5, SAA6D170E-6 and SAA6D170E-7. Each generation has its own parts.
| Generation | Description |
|---|---|
| Early 6D170 / SA6D170 / SAA6D170E-2 | Engines of earlier machines |
| SAA6D170E-3 | Found, for example, on the HD465-7, PC1250-7 and WA600-3 |
| SAA6D170E-5 | The subject of this article; arrangements by machine |
| SAA6D170E-6 | Found in Komatsu publications for a number of machines |
| SAA6D170E-7 | Engine of new-generation machines (WA600-8, D375A-8, PC1250LC/SP-11 and others) |
Parts for each generation are selected by catalogue number and Engine S/N — we check them for your machine.
11. Specifications by machine
All values come from the 170E-5 engine specification table (Komatsu manual); gross power at the flywheel, without fan. Power, torque and idle speed are set by the arrangement, not by «the engine in general».
| Machine | Power, kW (hp) / rpm | Max. torque, N·m / rpm | Idle: max. / min., rpm | Fuel consumption, g/(kW·h) | Dry weight, kg | Length × width × height, mm |
|---|---|---|---|---|---|---|
| D375A-5E0 | 452 (606) / 1,800 | 3,020 / 1,300 | 1,900 ± 20 / 720 ± 30 | 227 | 2,970 | 1,823 × 1,157 × 1,697 |
| D375A-5R | 452 (606) / 1,800 | 3,020 / 1,300 | 1,900 ± 20 / 750 ± 30 | 227 | 3,029 | 1,851 × 1,103 × 1,693 |
| PC1250-8 | 515 (690) / 1,800 | 3,025 / 1,300 | 2,000 ± 40 / 900 ± 25 | 218 | 3,140 | 1,783 × 1,176 × 1,707 |
| PC1250-8R | 515 (690) / 1,800 | 3,025 / 1,300 | 2,000 ± 40 / 900 ± 25 | 218 | 3,156 | 1,783 × 1,176 × 1,707 |
| WA600-6 | 396 (531) / 1,800 | 2,594 / 1,000 | 2,000 ± 50 / 800 ± 25 | 227 | 3,050 | 1,784 × 1,115 × 1,752 |
| WA600-6R | 396 (531) / 1,800 | 2,594 / 1,000 | 2,000 ± 50 / 800 ± 25 | 227 | 3,180 | 1,784 × 1,115 × 1,752 |
| HD465-7E0, HD605-7E0 | 552 (740) / 2,000 | 3,324 / 1,400 | 2,270 ± 50 / 750 ± 50 | 216 | 3,120 | 1,867 × 1,243 × 1,732 |
| HD465-7R, HD605-7R | 552 (740) / 2,000 | 3,324 / 1,400 | 2,270 ± 50 / 750 ± 50 | 216 | 3,028 | 1,852 × 1,297 × 1,644 |
Height is without the exhaust pipe. Common to all: 6 cylinders 170 × 170 mm, 23.15 L, firing order 1-5-3-6-2-4, DENSO ECD-U2 governor (electronic), oil 80 L, coolant 44 L (engine only), KOMATSU KTR130E turbocharger, «air-to-air» charge-air cooling; versions without «R» — with cooled EGR.
11.1. Power per the machine brochures and per the manual
The machine brochures give both gross and net power (gross per SAE J1995; net per ISO 9249 / SAE J1349), whereas the engine manual gives gross only. Small differences are caused by rounding and units: 514 kW (688 hp) in the PC1250-8 brochure and 515 kW (690 hp) in the manual; 551 and 552 kW for HD465/HD605. The metric «horsepower» (PS) differs from the American hp by 1.4 %. In the D375A-6 brochure the 474 kW rating is stated at 1,800 rpm (American edition) and at 1,900 rpm (European edition).
11.2. Calculated indicators
| Indicator | Formula | Value |
|---|---|---|
| Displacement | 6 × π/4 × 0.170² × 0.170 | 0.02315 m³ = 23.15 L |
| Volume of one cylinder | 23.152 L ÷ 6 | 3.86 L |
| Mean piston speed | 2 × stroke × speed | 10.2 m/s at 1,800; 11.3 m/s at 2,000 rpm |
| Brake mean effective pressure (BMEP) at maximum torque | 4π × T ÷ V | HD-7: ≈ 18.0 bar; PC1250-8: ≈ 16.4 bar; D375A-5: ≈ 16.4 bar (3,020 N·m); WA600-6: ≈ 14.1 bar |
| Specific output | Power ÷ displacement | HD-7: 23.8 kW/L (552 ÷ 23.15) |
These values help to understand the load: on the truck the engine works at the highest mean pressure and the highest speeds, on the loader at the lowest.
12. Weight and dimensions of the assemblies
| Assembly | Weight, kg |
|---|---|
| Cylinder block assembly (with liners) | 750 |
| Cylinder head × 6 | 46.5 each (279 total) |
| Crankshaft | 265 |
| Piston with connecting rod × 6 | 22 each (132 total); rod alone — 10.29 ± 0.03 |
| Camshaft | 51 |
| Front gear cover | 47 |
| Water pump | 16.2 |
| Oil pump | 10.2 |
| Flywheel | 36–82 (depending on the arrangement) |
| Flywheel housing | 150–170 (depending on the arrangement) |
| Oil pan | 56 |
| Turbocharger | 33.5–36 (depending on the arrangement); per the KTR130E description — 35.5 |
The sum of the main long block assemblies (block, heads, crankshaft, camshaft, pistons with rods, front cover, oil pump) is about 1.5 t. For comparison: the whole engine dry weighs 2.97–3.18 t, so the long block is roughly half of it.
In practice: a unit of this weight is handled only with lifting equipment and slings rated for the required load; the rigging method and lifting points are defined by the Komatsu manual for the machine.
Part III. Reference
This part is reference material. Dimensions, torques and standard values are taken from the Komatsu manual for the 170E-5 series engines, for comparison and for assessing the condition of parts. Before doing any work, check the edition of the manual for your Engine S/N: only it defines tolerances and tightening order. Units: dimensions in mm, torques in N·m (kgf·m in brackets), pressures in kPa or MPa.
13. Part dimensions and tolerances
13.1. Cylinder block and liners
| Parameter | Standard | Limit / action |
|---|---|---|
| Liner inside diameter | 170 (+0.040 / 0) | 170.24 — replace the liner |
| Out-of-round and taper of the inner surface | 0.020 | 0.08 — replace the liner |
| Liner protrusion above the block face | 0.07–0.15; difference between cylinders not more than 0.05 | Replace the liner or the block |
| Liner outside diameter, lower seating band | 194.565–194.615; interference in the block 0.025–0.135 | — |
| Liner outside diameter, upper seating band | 205.965–206.015 | — |
| Variation in depth of the upper flange in the block | — | 0.05 — correct by grinding |
| Liner outside diameter in the sealing ring zone | 190.24–190.29 | — |
| Block-to-liner clearance in the ring zone | 0.05–0.16 | Replace the liner or the block |
| Main bearing seat bore diameter (bolts tightened) | 148 (+0.025 / −0.001) | — |
| Main bearing shell thickness | 4.0 (−0.038 / −0.051) | — |
| Main bearing shell inside diameter | 140 (+0.127 / +0.076) | 140.20 |
| Bearing-to-journal clearance (main) | 0.076–0.152 | 0.32 — correct or replace |
| Interference of the main bearing cap in the block | 0.090–0.140 | 0.05 |
| Camshaft bushing inside diameter | 90 (+0.222 / +0.112) | 90.23 — replace |
| Camshaft bearing clearance | 0.077–0.217 | 0.25 |
| Out-of-flatness of the block surface under the head | 0.09 | 0.15 |
13.2. Crankshaft
| Journal size | Main journal, mm (standard / limit) | Rod journal, mm (standard / limit) |
|---|---|---|
| Standard (STD) | 140 (0 / −0.025) — limit 139.91 | 108.00 (0 / −0.022) — limit 107.91 |
| Undersize 0.25 | 139.75 — limit 139.66 | 107.75 — limit 107.66 |
| Undersize 0.50 | 139.50 — limit 139.41 | 107.50 — limit 107.41 |
| Undersize 0.75 | 139.25 — limit 139.16 | 107.25 — limit 107.16 |
| Undersize 1.00 | 139.00 — limit 138.91 | 107.00 — limit 106.91 |
- Journal out-of-round — not more than 0.010 (limit 0.015).
- Crankshaft end play — 0.14–0.32 (limit 0.6).
- Shaft runout (total indicator reading) — 0.09.
- Rear flange outside diameter — 170 ± 0.019.
- Main bearing shell thickness (at the middle) — 4.0 (−0.038 / −0.051), limit 3.90.
13.3. Camshaft and valve train
| Parameter | Standard | Limit |
|---|---|---|
| Intake lobe height | 78.233 ± 0.103 | 78.00 |
| Exhaust lobe height | 77.252 ± 0.103 | 77.00 |
| Camshaft journal diameter | 90 (−0.005 / −0.035) | 89.98 |
| Camshaft end play | 0.05–0.20 | 0.40 |
| Camshaft bend (indicator reading) | — | 0.20 |
| Valve recession | 0 | 0.80 |
| Valve head margin thickness: intake / exhaust | 3.2 / 3.3 | 2.7 / 2.8 |
| Seat angle: intake / exhaust | 30° ± 0°15′ / 45° ± 0°15′ | — |
| Valve stem diameter: intake / exhaust | 12 (−0.060 / −0.080) / 12 (−0.092 / −0.107) | 11.90 / 11.80 |
| Guide inside diameter | 12 | 12.10 |
| Valve guide protrusion | 43 ± 0.5 | — |
| Valve spring: free length / installed length | 99.6 / 87.4 mm; installed load 647 ± 65 N (66.0 ± 6.6 kgf) | Permissible load 608 N (62 kgf); out-of-squareness up to 2° |
| Rocker arm shaft-to-bushing clearance | 0.039–0.127 (shaft 45.0 −0.015/−0.028; bushing 45.0 +0.099/+0.024) | 0.16 |
| Valve clearance (cold): intake / exhaust | 0.32 / 0.62 (±0.02) | Adjust |
| Crosshead-to-guide clearance | 0.011–0.072 (diameters 13 +0.10/+0.05 and 13 +0.039/+0.028) | Adjust |
| Follower shaft: diameter / lever bore | 25 (−0.038 / −0.053) / 25 (+0.021 / 0) | — |
| Follower roller: outside diameter | 50 (+0.025 / 0) | 49.75 |
13.4. Connecting rod, piston, rings
| Parameter | Standard | Limit |
|---|---|---|
| Rod bushing-to-piston pin clearance | 0.030–0.055 (pin 68, 0 / −0.006; bushing +0.049 / +0.030) | 0.075 |
| Big-end bore of the connecting rod | 115 (+0.026 / 0) | — |
| Rod bearing-to-journal clearance | 0.058–0.132 | 0.34 |
| Rod bearing shell thickness: STD / 0.25 / 0.50 / 0.75 / 1.00 | 3.500 (−0.029 / −0.042) / 3.625 / 3.750 / 3.875 / 4.000 | 3.41 / 3.54 / 3.66 / 3.79 / 3.91 |
| Connecting rod bend / twist | — | 0.10 / 0.25 |
| Connecting rod weight | 10.29 ± 0.03 kg | — |
| Piston diameter (3.0 mm from the bottom, 20 °C, across the pin boss) | 170 (−0.135 / −0.165) | 169.79 |
| Piston pin bore / pin | 68 (+0.044 / +0.034) / 68 (0 / −0.006) | — |
| End gap of the top ring | 0.50–0.65 | 1.8 |
| End gap of the second ring | 0.70–0.85 | 1.8 |
| End gap of the oil ring | 0.50–0.70 | 1.8 |
Ring grooves are checked with a groove wear gauge or by the clearance between the piston and a new ring (the limit clearance is given in the manual for each ring type). The top and second rings are of the «keystone» type.
13.5. Gears, oil pump and water pump
| Pair / parameter | Standard | Limit |
|---|---|---|
| Front drive: crankshaft — large idler | 0.134–0.326 | 0.5 |
| Front drive: crankshaft — medium idler | 0.114–0.320 | — |
| Front drive: medium idler — alternator | 0.114–0.320 | 0.5 |
| Front drive: large idler — water pump | 0.121–0.333 | 0.5 |
| Front drive: large idler — oil pump | 0.121–0.333 | 0.5 |
| Rear drive: crankshaft — large idler | 0.155–0.412 | 0.6 |
| Rear drive: small idler — camshaft gear | 0.145–0.380 | 0.6 |
| Rear drive: camshaft gear — fuel pump gear | 0.007–0.559 | 0.6 |
| Bushing-to-shaft clearance of the front drive idler gears (two pairs) | 0.025–0.062 | 0.25 |
| End play of the front drive idler gears | 0.05–0.17 | 0.34 |
| Bushing-to-shaft clearance of the rear drive idler gear | 0.027–0.095 | 0.25 |
| End play of the rear drive idler gear | 0.04–0.18 | 0.3 |
| Oil pump: gear end clearance | 0.040–0.097 | — |
| Oil pump: gear radial clearance | 0.15–0.25 | — |
| Water pump: shaft interference in the bearings | 0.002–0.021 | — |
| Water pump: impeller-to-housing clearance | 0.26–0.68 | — |
Gear teeth: front drive — crankshaft 55, large idler 84, oil pump 38, water pump 31, small idler 67, alternator 55, EGR oil pump drive 43; rear drive — crankshaft 63, idlers 72 and 40, camshaft 70, fuel pump 70. Timing marks on the rear drive: crankshaft — idler, idler — crankshaft, camshaft — fuel pump gear.
14. Tightening torques
| Fastener | Order / step | Torque, N·m (kgf·m) |
|---|---|---|
| Head bolts (1)–(7); lubricate the thread and washer with anti-seize compound | 1st step | 245 (25), tolerance 235–255 |
| 2nd step | 382 (39), tolerance 373–392 | |
| 3rd step | additional turn of 90° (+30°/0) | |
| Head bolts (8)–(9) | — | 98 (10), tolerance 93–103 |
| Main bearing cap bolts; lubricate the thread and washer with engine oil | 1st step | 284 (29), tolerance 270–299 |
| 2nd step | 569 (58), tolerance 559–579 | |
| 3rd step | additional turn of 90° (+30°/0) | |
| Connecting rod cap bolts; lubricate the thread and washer with engine oil | 1st step | 196 (20), tolerance 186–206 |
| 2nd step | additional turn of 90° (+15°/0) | |
| Crankshaft pulley bolt | 1st step | 74 (7.5), tolerance 54–93 |
| 2nd step | 245 (25), tolerance 226–265 | |
| 3rd step | 637 (65), tolerance 618–657 | |
| Injector mounting bolt | — | 66.7 (6.75), tolerance 58.8–73.5 |
| Rocker housing bolt | — | 86 (8.75), tolerance 78–93 |
| Head cover bolts: cylinders no. 1, 3–6 | — | 10 (1), tolerance 9–11 |
| Head cover bolts: cylinder no. 2 | — | 66.7 (6.75), tolerance 58.8–73.5 |
| High-pressure tube (injection) | — | 41.7 (4.25), tolerance 39.2–44.1 |
| Rocker arm adjusting screw locknut | — | 68 (6.9), tolerance 58–77 |
| Crosshead locknut | — | 59 ± 6 (6.0 ± 0.6) |
The head bolts are tightened in the order of numbering (1)–(9) according to the manual's diagram. For angle-tightening steps, new bolts or bolts that pass the manual's criteria are used.
| Thread diameter, mm | Wrench size, mm | Torque, N·m | Torque, kgf·m |
|---|---|---|---|
| 6 | 10 | 11.8–14.7 | 1.2–1.5 |
| 8 | 13 | 27–34 | 2.8–3.5 |
| 10 | 17 | 59–74 | 6.0–7.5 |
| 12 | 19 | 98–123 | 10.0–12.5 |
| 14 | 22 | 153–190 | 15.5–19.5 |
| 16 | 24 | 235–285 | 23.5–29.5 |
| 18 | 27 | 320–400 | 33.0–41.0 |
| 20 | 30 | 455–565 | 46.5–58.0 |
| 22 | 32 | 610–765 | 62.5–78.0 |
| 24 | 36 | 785–980 | 80.0–100.0 |
| 27 | 41 | 1,150–1,440 | 118–147 |
| 30 | 46 | 1,520–1,910 | 155–195 |
| 33 | 50 | 1,960–2,450 | 200–250 |
| 36 | 55 | 2,450–3,040 | 250–310 |
| 39 | 60 | 2,890–3,630 | 295–370 |
For bolts with a different head type (fig. B of the manual) and for flange, fitting and hose connections the manual gives separate tables — this is a general Komatsu reference for all engines, not special values for the 170E-5.
15. Standard values for checking the engine
The «standard for a new engine / criterion» table from the manual: it is used to decide whether the engine is in good condition in terms of boost pressure, exhaust and oil pressure. Values are at rated power unless stated otherwise.
| Parameter | D375A-5E0 | D375A-5R | PC1250-8 | PC1250-8R | WA600-6 | WA600-6R | HD-7E0 | HD-7R |
|---|---|---|---|---|---|---|---|---|
| High idle speed, rpm | 1,900 ± 20 | 1,900 ± 20 | 2,000 ± 40 | 2,000 ± 40 | 2,000 ± 50 | 2,000 ± 50 | 2,270 ± 50 | 2,270 ± 50 |
| Low idle speed, rpm | 750 ± 20 | 750 ± 20 | 900 ± 25 | 900 ± 25 | 800 ± 25 | 800 ± 25 | 750 ± 50 | 750 ± 50 |
| Boost pressure, kPa (min.) | 141.3 / 128 | 113.3 / 100 | 160 / 147 | 116 / 102.6 | 126.6 / 113.3 | 94 / 80.6 | 160 / 147 | 130.6 / 117.3 |
| Exhaust gas pressure, kPa (min.) | 159.3 / 146 | 120 / 106.6 | 148 / 134.6 | 123 / 109 | 155 / 141 | 110.6 / 97.3 | 161 / 148 | 132 / 119 |
| Exhaust gas temperature, °C (max.) | 700 / 730 | 680 / 700 | 720 / 740 | 700 / 730 | 680 / 700 | 710 / 740 | 710 / 740 | 680 / 700 |
| Smoke density at sudden acceleration, Bosch (max.) | 2.5 / 3.5 | 3.5 / 4.5 | 4.5 / 5.5 | 4.5 / 5.5 | 4.0 / 5.0 | 4.0 / 5.0 | 4.0 / 5.0 | 4.0 / 5.0 |
| Crankcase gas pressure (blow-by), kPa (max.) | 3.43 / 9.41 | 3.43 / 9.41 | 3.43 / 12.94 | 3.43 / 12.94 | 3.43 / 9.41 | 3.43 / 9.41 | 3.43 / 12.94 | 3.43 / 12.94 |
| Oil consumption, % of fuel consumption (max.) | 0.1 / 0.3 | 0.1 / 0.3 | 0.15 / 0.3 | 0.15 / 0.3 | 0.1 / 0.3 | 0.15 / 0.3 | 0.1 / 0.3 | 0.1 / 0.3 |
| Oil pressure at idle, MPa (min.) | 0.12 / 0.08 | 0.10 / 0.08 | 0.10 / 0.08 | 0.10 / 0.08 | 0.10 / 0.08 | 0.10 / 0.08 | 0.10 / 0.08 | 0.10 / 0.08 |
Same for all machines: intake resistance — not more than 3.73 kPa (criterion 7.5); smoke density at rated power — not more than 1.5 Bosch (criterion 2.5), at high idle — not more than 1.0 (criterion 2.0); valve clearances 0.32 (intake) and 0.62 mm (exhaust); compression pressure with oil at 40–60 °C and 210–250 rpm — not less than 2.94 MPa (30 kgf/cm²), criterion 2.1 MPa (21); oil pressure at rated power (oil not colder than 80 °C) — not less than 0.39 MPa (4.0 kgf/cm²), criterion 0.24 MPa (2.4); oil temperature — 90–110 °C, limit 120 °C; starting speed — not less than 125 rpm at 0 °C without starting aids and 85 rpm at −20 °C with starting aids; for EGR versions the drive pressure of the EGR valve and bypass — not less than 1.18 MPa (12 kgf/cm²) at low idle and 1.43 MPa (14.6 kgf/cm²) at high idle.
16. Load run-in and acceptance tests
The manual describes a bench run-in in five steps with a total duration of 30 minutes (1.5 + 4.5 + 9 + 12 + 3). Values are given without fan, dynamometer arm 716 mm; fuel ASTM No. 1 or No. 2 diesel, oil SAE 15W-40. An assembled long block is run in according to the rules of the unit's manufacturer and the machine manual; this table is a reference guide, not an obligation.
| Machine | Parameter | 1 (1.5 min) | 2 (4.5 min) | 3 (9 min) | 4 (12 min) | 5 (3 min) |
|---|---|---|---|---|---|---|
| D375A-5E0, D375A-5R | Speed, rpm | 750 | 1,134 | 1,422 | 1,638 | 1,800 |
| Dynamometer load, N (kgf) | 0 | 1,327 (135) | 2,117 (216) | 2,757 (281) | 3,345 (341) | |
| Power, kW (hp) | 0 | 113 (152) | 226 (303) | 339 (455) | 452 (606) | |
| PC1250-8, PC1250-8R | Speed, rpm | 900 | 1,134 | 1,422 | 1,638 | 1,800 |
| Load, N (kgf) | 0 | 1,513 (154) | 2,414 (246) | 3,143 (321) | 3,814 (389) | |
| Power, kW (hp) | 0 | 129 (173) | 257 (345) | 386 (518) | 515 (690) | |
| WA600-6, WA600-6R | Speed, rpm | 800 | 1,134 | 1,422 | 1,638 | 1,800 |
| Load, N (kgf) | 0 | 1,163 (119) | 1,855 (189) | 2,416 (246) | 2,931 (299) | |
| Power, kW (hp) | 0 | 99 (133) | 198 (266) | 297 (398) | 396 (531) | |
| HD465-7E0/-7R, HD605-7E0/-7R | Speed, rpm | 750 | 1,260 | 1,580 | 1,820 | 2,000 |
| Load, N (kgf) | 0 | 1,459 (149) | 2,328 (237) | 3,031 (309) | 3,677 (375) | |
| Power, kW (hp) | 0 | 138 (185) | 276 (370) | 414 (555) | 552 (740) |
| Indicator | D375A-5E0 / -5R | PC1250-8 / -8R | WA600-6 / -6R | HD465/605-7E0 / -7R |
|---|---|---|---|---|
| Rated power (gross), kW (hp) | 438–465 (587–624) | 499–530 (669–711) | 384–407 (515–546) | 535–568 (718–762) |
| Load at rated power, N (kgf) | 3,245–3,446 (331–351) | 3,697–3,932 (377–401) | 2,844–3,020 (290–308) | 3,570–3,788 (364–386) |
| Maximum torque (gross), N·m (kgf·m) | 2,932–3,109 (299–317) | 2,932–3,119 (299–318) | 2,520–2,667 (257–272) | 3,226–3,423 (329–349) |
| Load at maximum torque, N (kgf) | 4,089–4,344 (417–443) | 4,097–4,354 (418–444) | 3,510–3,727 (358–380) | 4,501–4,776 (459–487) |
| Fuel consumption, time for 500 cm³ | not less than 14 s | not less than 12 s | not less than 16 s | not less than 12 s |
| Coolant / oil temperature, °C | 70–90 / 90–110 | |||
| Oil pressure at rated power, kPa | 392–539 | 392–539 | 392–569 | 392–539 |
| Oil pressure at maximum torque, kPa | 294–539 | 294–442 | 226–343 | 343–539 |
| Oil pressure at high idle / at low idle, kPa | 392–539 / not less than 118 | |||
| Exhaust gas temperature at rated power, °C (max.) | 650 (-5E0) / 630 (-5R) | 680 (-8) / 650 (-8R) | 650 (-6) / 600 (-6R) | 670 (-7E0) / 650 (-7R) |
| Exhaust gas temperature at max. torque, °C (max.) | 700 / 680 | 720 / 700 | 680 / 710 | 710 / 680 |
17. Catalogue numbers of the main parts
The numbers of the main parts of the SAA6D170E-5 engine help you find the items you need quickly. We confirm the exact number for your engine from its Engine S/N and the machine model.
| № | Part | Number |
|---|---|---|
| 1 | Cylinder block | 6245-21-1100 |
| 2 | Crankshaft assembly | 6245-31-1100 |
| 3 | Connecting rod assembly | 6245-31-3100 |
| 4 | Piston | 6245-31-2110 |
| 5 | Ring set per piston | 6245-31-2010 |
| 6 | Piston pin | 6248-31-2410 |
| 7 | Main bearing shells STD | 6240-21-8100 |
| 8 | Rod bearing shells STD | 6162-33-3041 |
| 9 | Camshaft assembly | 6245-41-1100 |
| 10 | Cylinder head assembly | 6245-11-1100 |
| 11 | Intake valve | 6240-41-4110 |
| 12 | Exhaust valve | 6240-41-4220 |
| 13 | Cylinder head gasket STD | 6240-11-1810 |
| 14 | Valve crosshead | 6240-41-5610 |
| 15 | Valve stem seal | 6240-11-1370 |
| 16 | Oil pump assembly | 6240-51-1100 |
| 17 | Water pump assembly | 6240-61-1102 |
18. Komatsu numbers: long blocks, short blocks, remanufactured engines
| Number | What it is | Note |
|---|---|---|
6245-LE-0100 | Long block (new number) | Long block of the SAA6D170E-5 engine |
RM6245-LE-0100 | Long block with the RM prefix (remanufactured) | Remanufactured (reman) variant of the 6245-LE-0100 long block |
6245-SE-0011 | Short block | HD465-7E0/-7R, HD605-7E0/-7R |
6245-SE-0021 | Short block | D375A-5E0/-5R/-6/-6R |
6245-SE-0031 | Short block | PC1250-8, PC1250LC-8, PC1250SP-8 and -8R variants |
6245-SE-0041 | Short block | WA600-6, WA600-6R |
RM6245-A0-0030 | Complete remanufactured engine | 6D170 for the WA600-6 |
RM6245-B0-0030 | Complete remanufactured engine | HD465-7E0 |
RM6245-A0-0013 | Complete remanufactured engine | SAA6D170E |
RM6245-C0-0111 | Complete remanufactured engine | PC1250LC-8 |
RM6245-E0-0010 | Complete remanufactured engine | D375A-6, SAA6D170E-5 |
RM6245-D0-0010 | Complete remanufactured engine | SA6D170E-5, D375A-5E0 |
The short block number 6245-SE-0040 is shown in the catalogue as superseded.
19. Diagnostics and defect inspection: what data is needed
A data-collection scheme for inspection: wear limits and torques come from sections 13–15 and from the manual for your Engine S/N.
19.1. Before disassembly
Record the full engine marking, the Engine S/N, the model and the Machine S/N and, where possible, keep the fault codes and the service history. Describe the complaint: oil pressure, oil consumption, loss of power, overheating, smoke, hard starting, contamination of the fuel or coolant, noises, leaks. The same symptoms have different causes. Low oil pressure does not prove an oil pump fault: take into account oil temperature, viscosity, the sensor, filters, bearing clearances and measurement conditions. Increased fuel consumption does not equal «piston wear» without checking injection, air, EGR, load and electronic control.
19.2. Mechanical part
Block and liners — geometry and fits; crankshaft — journals, runout, cracks; connecting rods — geometry and bushings; pistons — surfaces and rings; heads — sealing, seats, guides, valve train. Each operation needs a specific fitness criterion from the manual (section 13), not a commercial generalisation «new/used is acceptable».
19.3. Lubrication, cooling, fuel
The oil pump and passages, the heat-exchange surfaces and both oil coolers, the water pump and thermostat, boost, the cleanliness of the fuel system and the injectors are assessed separately. If a long block is to be installed, agree the list of attachments to be transferred before ordering, so that during installation it does not turn out that necessary units are missing or do not match in fit and control.
20. Operation: what depends on the machine
Maintenance depends on the machine the engine is installed in. Fill volumes in the brochures differ because they refer to the installation in the machine.
| Machine | What Komatsu states | Comment |
|---|---|---|
| Engine (specification table) | 80 L (fill), coolant 44 L | A value for the engine; the volume «in the machine» depends on the sump and oil lines |
| HD465-7R | Engine oil 80 L (machine service table) | For the HD465-7R dump truck |
| WA600-6 | Engine 86 L (service table) | Depends on the configuration of the lubrication system |
| PC1250-8 (Japanese specification) | 97 L total, 86 L replaceable | Total and replaceable volumes are different indicators |
For the HD465-7R a Komatsu publication gives an engine oil change interval of 500 hours. Oils recommended in the manual for the pressure check: SAE 0W-30 (E0S), 5W-40 (E0S), 10W-30 (DH), 15W-40 (DH), 30 (DH). Take the current intervals and oil grades from the Operation & Maintenance Manual of your machine.
Service life. Engine life in hours is not fixed by a single figure: it depends on the application, the quality of maintenance, fuel, working conditions and repair history. High thermal loads, dusty mines, long driving under load, a large share of idling, contaminated fuel and temperature-regime violations make regular maintenance especially important.
Conclusion
The Komatsu SAA6D170E-5 long block is the ready mechanical core of the engine: cylinder block, crankshaft, pistons with connecting rods, cylinder heads with valves and the valve train. It is selected for the arrangement and serial number of your engine, while the attached equipment is carried over from the old unit. The engine data in Parts II and III is what makes that selection exact.
The Komatsu SAA6D170E-5 is not a single «530 or 739 hp engine» but a technical platform of powerful 23.15 L diesels with different machine and regional arrangements. Komatsu documents confirm its use in HD465/HD605-7E0/7R dump trucks, D375A-6 dozers and related versions, PC1250-8 excavators and WA600-6 loaders.
Five questions are enough for a correct selection: which exact engine is fitted, what is its serial number, which machine it works in, which unit is really needed and which catalogue number confirms the applicability. This way you avoid the most expensive mistakes — ordering an unsuitable block, piston, valve kit, short block or long block. If you need a REMAN long block — send us a photo of the engine nameplate and the machine serial number.
Questions and answers
What is a long block?
A long block is an engine without attachments: cylinder block, crankshaft, pistons with connecting rods, cylinder heads with valves and the valve timing mechanism. The turbocharger, the high-pressure fuel system, manifolds, electronics and other attachments are usually transferred from the old engine.
How does a long block differ from a short block?
A short block is the lower part: cylinder block, crankshaft, pistons, connecting rods, liners (oil cooler — optional), without the heads. A long block includes the cylinder heads and the valve timing. A complete engine is the whole power unit.
What does a long block include according to the Komatsu configuration?
Typical configuration: complete heads, intake and exhaust valves, cylinder block, front drive gears, crankshaft, pistons and connecting rods, camshaft and cam followers, rocker arms, oil pump, injectors (for electronic fuel systems). The front gear cover, oil cooler and water pump are optional. The scope of each unit is stated in its specification.
What is the long block number for the SAA6D170E-5?
In Komatsu nomenclature the long block of the SAA6D170E-5 engine corresponds to the numbers 6245-LE-0100 (new) and RM6245-LE-0100 (remanufactured, RM prefix). The 6245 series belongs to this engine.
What does RM mean in RM6245-LE-0100?
The RM prefix in Komatsu numbering denotes remanufactured (reman) items: RM6245-LE-0100 is the reman variant of the 6245-LE-0100 long block.
What information is needed to select a long block?
The full engine name with the arrangement letter, the Engine S/N (photo of the nameplate), the machine model and serial number, the required assembly level (block, short block, long block, complete engine), the known number of the previous part and photos of the old engine from the front and both sides.
Will the long block fit my machine?
It is defined by a chain: catalogue number → exact arrangement (-5A, -5BR, -5C…) → Engine S/N → machine model → Machine S/N → catalogue check. Send us a photo of the engine nameplate and the machine serial number — we will check the arrangement and select the unit.
Can a long block be installed on an engine with a different arrangement letter?
We select by Engine S/N: the base engine is the same, the ancillaries are transferred, and internal revisions (for example, the split of the cylinder block within the -5E by serial numbers) are taken into account in our selection.
Is this a Komatsu product?
Yes. It is an original Komatsu Reman remanufactured unit, not a copy. Identification data for each unit (a photo of the data plate, the serial number) are provided on request.
What is the number of your long block?
The unit is identified by its own nameplate and serial number. For catalogue search the reference numbers 6245-LE-0100 and RM6245-LE-0100 are used.
What warranty does the long block have?
The warranty on long blocks is agreed individually and recorded in the specification or invoice for the specific unit.
When will a REMAN long block for the SAA6D170E-5 be in stock?
The first lot — 3 units — is in transit and is expected in February 2027 at the CATKOMPARTS warehouse in Guarulhos (São Paulo, Brazil). Delivery to other countries — on request; payment before shipment.
Can a long block from the WA600-6 be installed on the D375A-6?
A long block is selected for a specific engine arrangement: the WA600-6 and D375A-6 have different arrangements and different short block numbers, so we check the catalogue number and Engine S/N and select the suitable unit.
Which short blocks exist for the SAA6D170E-5?
Four numbers by machine group: 6245-SE-0011 (HD465/HD605-7E0 and -7R), 6245-SE-0021 (D375A-5E0/-5R/-6/-6R), 6245-SE-0031 (PC1250-8 and -8R variants), 6245-SE-0041 (WA600-6/-6R). We confirm the exact number for your engine by its Engine S/N.
Which short block is needed for the PC1250-8?
For the PC1250-8 group the number is 6245-SE-0031; we confirm the exact number by Engine S/N.
Which short block is needed for the D375A-6?
For the D375A group the number is 6245-SE-0021.
Which short block is needed for the HD465-7R?
For the HD465/HD605-7R group 6245-SE-0011 is listed.
Which short block is needed for the WA600-6?
For the WA600-6 group 6245-SE-0041 is listed.
What does SAA6D170E-5 mean?
It is a model of the Komatsu 6D170 engine family. S — turbocharging, AA — «air-to-air» charge-air cooling, 6D — six cylinders in line (diesel), 170 — cylinder bore in mm, E — generation designation, «-5» — series. The letter after the series (for example -5A, -5BR) is the arrangement for a specific machine.
How many cylinders does the SAA6D170E-5 have and what is its displacement?
Six cylinders in line, displacement 23.15 L (23,152 cm³), bore and stroke 170 × 170 mm, firing order 1-5-3-6-2-4.
How many horsepower does the SAA6D170E-5 have?
There is no single figure: power depends on the machine. Total power (gross): WA600-6 — 396 kW (531 hp) at 1,800 rpm; D375A-5 — 452 kW (606 hp), D375A-6 — 474 kW (636 hp) per the brochure; PC1250-8 — 515 kW (690 hp) per the engine manual (514 kW, 688 hp per the brochure); HD465/HD605-7 — 552 kW (740 hp) at 2,000 rpm. Net power is lower.
Which machines is the SAA6D170E-5 fitted to?
HD465-7E0/-7R and HD605-7E0/-7R dump trucks; D375A-5E0/-5R and D375A-6/-6R dozers; PC1250-8, PC1250LC-8, PC1250SP-8 excavators and -8R variants; WA600-6/-6R wheel loaders; WD600-6/-6R wheeled dozers (per Komatsu's own publications).
What is the torque of the SAA6D170E-5?
Maximum torque (gross): WA600-6 — 2,594 N·m at 1,000 rpm; D375A-5 — 3,020 N·m at 1,300 rpm; PC1250-8 — 3,025 N·m at 1,300 rpm; HD465/HD605-7 — 3,324 N·m at 1,400 rpm.
What is the difference between the «R» and non-«R» versions?
The «R» at the end of a machine name denotes a regional version, not reman. According to the Komatsu manual, engines of the «R» versions are built without an EGR system (the manual has separate tables for them), and the machine brochures give them Tier 2 / Stage 2 (or equivalent); versions without «R» have cooled EGR, Tier 3 / Stage 3A.
How does the SAA6D170E-5 differ from the SAA6D170E-3 and SAA6D170E-7?
These are different generations. The SAA6D170E-3 is found, for example, on the HD465-7 without the E0/R index, the PC1250-7 and the WA600-3; the SAA6D170E-7 is fitted to new-generation machines (WA600-8, D375A-8, PC1250-11). Parts for each generation are selected by catalogue number and Engine S/N.
Can parts of the -7 engine be used on the -5 engine?
Parts of the -5 and -7 engines belong to different generations and are selected by catalogue number and Engine S/N — we will select the right item.
What are the tightening torques for the cylinder head and the main bearings?
Head bolts (1)–(7): 245 → 382 N·m, then an additional 90° turn; bolts (8)–(9): 98 N·m. Main bearing cap bolts: 284 → 569 N·m, then an additional 90° turn. Connecting rod cap bolts: 196 N·m, then an additional 90° turn. More in section 14; always check the manual for your Engine S/N.
What are the valve clearances on the SAA6D170E-5?
With the engine cold: intake valves 0.32 mm, exhaust valves 0.62 mm (tolerance ±0.02).
What is the permissible cylinder liner diameter?
Standard inside diameter — 170 mm (+0.040/0); repair limit — 170.24 mm. Out-of-round and taper — standard 0.020, limit 0.08 mm.
What is the normal compression pressure?
Not less than 2.94 MPa (30 kgf/cm²) with oil at 40–60 °C and 210–250 rpm; decision criterion — 2.1 MPa (21 kgf/cm²).
How much oil does the SAA6D170E-5 need?
There is no single figure without the machine. The engine specification table gives 80 L fill; machine service tables show 80 L (HD465-7R) and 86 L (WA600-6); for the PC1250-8 the Japanese publication distinguishes 97 L total and 86 L replaceable volume. Use the operation manual of the machine.
How much do the engine and the long block weigh?
The dry mass of the engine is 2,970 to 3,180 kg depending on the arrangement. The main long block units (block 750 kg, 6 heads 279 kg, crankshaft 265 kg, pistons with connecting rods 132 kg, camshaft 51 kg, front cover 47 kg, oil pump 10.2 kg) add up to about 1.5 t.
Why do the documents show different piston numbers — 6245-31-2110 and 6246-31-2110?
Komatsu publishes both numbers as separate items; the piston is selected by engine arrangement, serial range and dimensions.
What should you tell us for an exact order?
The full engine model with the arrangement letter, Engine S/N, machine model and Machine S/N, the required assembly level and the previous part number, if known. We check the rest ourselves and send you the specification.
Glossary of terms
- Long Block
- The mechanical assembly of the engine: block, crankshaft, pistons with connecting rods, heads with valves, valve timing (in the typical Komatsu configuration — also the drive, oil pump, etc.), without most of the attachments.
- Short Block
- The lower part of the engine: block, crankshaft, pistons, connecting rods, liners (oil cooler — optional), without the heads.
- Complete Engine
- The whole power unit; the scope of attachments is defined by the number.
- REMAN / remanufactured
- A unit disassembled, cleaned, inspected and assembled with parts replaced or restored to specified dimensions.
- ESN / Engine S/N
- The engine serial number from the nameplate. It defines the applicability limits of parts in the catalogue.
- Machine S/N
- The machine serial number. It does not replace the Engine S/N.
- Gross / Net
- Total power at the flywheel (SAE J1995) and net power with the equipment installed (ISO 9249 / SAE J1349).
- Common Rail (HPCR)
- A fuel system with a common high-pressure rail and electronic injection control; here, up to 160 MPa.
- EGR
- Exhaust gas recirculation; on the 170E-5 engine (versions without «R») — cooled, with hydraulic valve actuation.
- Tier 3 / Stage 3A; Tier 2 / Stage 2
- US/EU emission classes; for versions with EGR and without EGR (R) respectively, per the machine brochures.
- Undersizes (US)
- Reduced crankshaft journal sizes of 0.25 / 0.50 / 0.75 / 1.00 mm and the corresponding thicker bearing shells.
- Supersession (replacement of a number)
- An official replacement of one part number by another in the manufacturer's catalogue.
- Plateau honing
- Plateau honing — treatment of the liner surface with smooth «plateaus» and valleys to hold oil.
Sources
The reference data in this article is based on the following Komatsu documents and publications.
- Komatsu, manual for the 170E-5 series engines: SEN00195 (specifications, weight, curves), SEN00197 (construction and maintenance standards), SEN00367 (standard values, run-in, tests) — for the Engine S/N of a specific edition, request the current version.
- Komatsu, machine brochure HD465-7R, CEN00178-05: komatsu.com
- Komatsu, brochure WA600-6, CEN00056-04: komatsu.com
- Komatsu, brochure WA600-6R, CEN00209-04: komatsu.com
- Komatsu, brochure D375A-6, CEN00372-03: komatsu.com
- Komatsu, brochure PC1250-8 / PC1250SP-8, CEN00102-03; regional specification of the PC1250-8 (Komatsu Japan): komatsu.jp
- Komatsu, brochure HD605-7R: komatsu.jp; HD605-7E0: komatsu.com.br; HD465-7E0: komatsu.com
- Komatsu, WD600-6 (machine page) and WD600-6R, CEN00726-00 (brochure)
- Komatsu, new-generation machines: WA600-8, D375A-8, PC1250LC-11
- Komatsu, part listings: 6240-21-2220, 6245-31-2110, 6246-31-2110
- Komatsu America press releases on the D375A-6, WD600-6, HD605-7 and PC1250-8 (history of the generation and cooled EGR).
Komatsu® is a registered trademark of Komatsu Ltd. The brand name, engine and machine model designations and part numbers are used only to indicate the application of this product and for identification. CATKOMPARTS (Catkom Parts) supplies original Komatsu Reman remanufactured units, not copies.
18/11/2026


